An intumescent is a substance that swells as a result of heat exposure, thus leading to an increase in volume and decrease in density. Intumescents are typically used in passive fire protection and require listing, approval, and compliance in their installed configurations in order to comply with the national building codes and laws.[citation needed]

The details for individual building parts are specified in technical standards which are compiled and published by national or international standardization bodies like the British Standards Institute (BSI), the German Institute for Standardization (DIN), the American Society for Testing and Materials (ASTM) or the International Standardization Organization (ISO).

Intumescent coatings for steel constructions must be approved in standardized fire tests. Some important fire test standards are listed below:

  • European Union: EN 13381-8 (Replaces national Standards in Europe)
  • United Kingdom: BS 476-20/21 (Commonly referred to in EU, Middle and Far East)
  • United States: ASTM E119 (Equivalent to UL 263, referred to in Middle and Far East), UL 1709 (Test using the hydrocarbon fire curve)
  • Russia: VNIIPO (Also used in former Soviet Union countries)
  • Chile: NCh 1974
  • China: GB 14907
  • South Korea: KS F2257 1,6,7
  • Taiwan: CNS 11728


Soft charEdit

These intumescents produce a light char, which is a poor conductor of heat, thus retarding heat transfer. Typically the light char consist of microporous carbonaceous foam formed by a chemical reaction of three main components: ammonium polyphosphate, pentaerythritol and melamine.[citation needed] The reaction takes place in a matrix formed by the molten binder which is typically based on vinyl acetate copolymers or styrene acrylates.

Ablative coatings contain a significant amount of hydrates. When the hydrates are heated, they decompose, and water vapour is released, which has a cooling effect. Once the water is spent, the insulation characteristics of the char that remains can slow down heat transfer from the exposed side to the unexposed side of an assembly.

Soft char products are typically used in thin film intumescents for fireproofing structural steel as well as in firestop pillows. Typically, the expansion pressure that is created for these products is very low, because the soft carbonaceous char has little substance, which is beneficial if the aim is to produce a layer of insulation.

Hard charEdit

Harder chars are produced with sodium silicates and graphite. These products are suitable for use in plastic pipe firestops as well as exterior steel fireproofing. In those applications, it is necessary to produce a more substantial char capable of exerting quantifiable expansion pressure. In the case of firestops, a melting, burning plastic pipe must be squeezed together and shut so that there will be no opening for fire to propagate to an otherwise fire-resistance rated wall or floor assembly. In the case of exterior fireproofing, a hydrocarbon fire must be held off with quite potentially more kinetic energy than a house fire. Intumescents that produce hard chars are unsuitable for interior spray fireproofing.

Intumescent coatingsEdit

Intumescent coatings may be designed for protection of metals (primarily steel) from fire. They may be based on a number of resin binders including epoxy, and silicone.[1] Melamine-formaldehyde resin systems have even been used using layered double-hydroxide modified phosphate esters that improved the intumescent properties and also made an improvement to the smoke suppression properties.[2]


Intumescents are used to achieve passive fire protection for such applications as firestopping, fireproofing, gasketing and window casings. Such applications are relevant for buildings, offshore constructions, ships and aircraft.


Some intumescents are susceptible to environmental influences, such as humidity, which can reduce or negate their ability to function. In Germany, the Deutsches Institut für Bautechnik, DIBt,[3] quantifies the ability of intumescents to stand the test of time against various environmental exposures. DIBt-approved firestops and fireproofing materials are available in Canada and the U.S.


See alsoEdit


  1. ^ Cardoso, de Sa, Beraldo, Hidalgo and Ferreira (November 2020). "Intumescent coatings using epoxy, alkyd, acrylic, silicone and silicone-epoxy hybrid resins for steel fire protection". Journal of Coatings Technology and Research. 17 (6): 1471–1488. doi:10.1007/s11998-020-00366-9.{{cite journal}}: CS1 maint: multiple names: authors list (link)
  2. ^ Xu, Deng and Lang (January 2020). "Flame retardancy and smoke suppression properties of transparent intumescent fire-retardant coatings reinforced with layered double hydroxides". Journal of Coatings Technology and Research. 17 (1): 157–169. doi:10.1007/s11998-019-00249-8.
  3. ^ DIBt (Deutsches Institut für Bautechnik), a state-level authority concerned with technical matters related to construction (building regulations, design, testing, certification, safety, building equipment, approvals, etc.
  4. ^ "S-115".

External linksEdit

  • "The proof is in the fire" Chemical Innovation Magazine, American Chemical Society
  • Article about intumescent materials
  • Translation of DIBt test procedure for intumescent building products
  • Translation of DIBt test procedure for reactive spray fireproofing materials
  • American Chemical Society: Fire Retardancy of Polypropylene Composites Using Intumescent Coatings
  • ASTM E 2786 - 2010 Standard Test Methods for Measuring Expansion of Intumescent Materials Used in Firestop and Joint Systems