The iodine value (or iodine adsorption value or iodine number or iodine index, commonly abbreviated as IV) in chemistry is the mass of iodine in grams that is consumed by 100 grams of a chemical substance. Iodine numbers are often used to determine the amount of unsaturation in fats, oils and waxes. In fatty acids, unsaturation occurs mainly as double bonds which are very reactive towards halogens, the iodine in this case. Thus, the higher the iodine value, the more unsaturations are present in the fat. It can be seen from the table that coconut oil is very saturated, which means it is good for making soap. On the other hand, linseed oil is highly unsaturated, which makes it a drying oil, well suited for making oil paints.
The determination of iodine value is a particular example of iodometry. A solution of iodine I2 is yellow/brown in color. When this is added to a solution to be tested, however, any chemical group (usually in this test -C=C- double bonds) that react with iodine effectively reduce the strength, or magnitude of the color (by taking I2 out of solution). Thus the amount of iodine required to make a solution retain the characteristic yellow/brown color can effectively be used to determine the amount of iodine sensitive groups present in the solution.
The chemical reaction associated with this method of analysis involves formation of the diiodo alkane (R and R' symbolize alkyl or other organic groups):
In a typical procedure, the fatty acid is treated with an excess of the Hanuš or Wijs solution, which are, respectively, solutions of iodine monobromide (IBr) and iodine monochloride (ICl) in glacial acetic acid. Unreacted iodine monobromide (or monochloride) is then allowed to react with potassium iodide, converting it to iodine I2, whose concentration can be determined by back-titration with sodium thiosulfate (Na2S2O3) standard solution.
The basic principle of iodine value was originally introduced in 1884 by A. V. Hübl as “Jodzahl”. He used iodine alcoholic solution in presence of mercuric chloride (HgCl2) and carbon tetrachloride (CCl4) as fat solubilizer. [Note 1] The residual iodine is titrated against sodium thiosulfate solution with starch used as endpoint indicator. This method is now considered as obsolete.
J. J. A. Wijs introduced modifications in Hübl method by using iodine monochloride (ICl) in glacial acetic acid, which became known as Wijs's solution, dropping the HgCl2 reagent. Alternatively, J. Hanuš used iodine monobromide (IBr), which is more stable than ICl when protected from light. Typically, fat is dissolved in chloroform [Note 2] and treated with excess ICl/IBr, Some of the halogen reacts with the double bonds in the unsaturated fat while the rest remains.
Afterward, the liberated I2 is titrated against sodium thiosulfate, in presence of starch, to indirectly determine the concentration of the reacted iodine.
IV (g I/ 100 g) is calculated from the formula :
The determination of IV according to Wijs is the official method currently accepted by international standards such as DIN 53241-1:1995-05, AOCS Method Cd 1-25, EN 14111 and ISO 3961:2018. One of the major limitations of is that halogens does not react stoichiometrically with conjugated double bonds (particularly abundant in some drying oils). Therefore, Rosenmund-Kuhnhenn method makes more accurate measurement in this situation.
Proposed by H. P. Kaufmann in 1935, it consists in the bromination of the double bonds using an excess of bromine and anhydrous sodium bromide dissolved in methanol. The reaction involves the formation of a bromonium intermediate as follows:
Then the unused bromine is reduced to bromide with iodide (I−).
Now, the amount of iodine formed is determined by back-titration with sodium thiosulfate solution.
The reactions must be carried out in the dark, since the formation of bromine radicals is stimulated by light. This would lead to undesirable side reactions, and thus falsifying a result consumption of bromine.
For educational purposes, Simurdiak et al. (2016) suggested the use of pyridinium tribromide as bromination reagent which is more safer in chemistry class and reduces drastically the reaction time.
This method is suitable for the determination of iodine value in conjugated systems (ASTM D1541). It has been observed that Wijs/ Hanuš method gives erratic values of IV for some sterols (i.e. cholesterol) and other unsaturated components of insaponifible fraction. The original method uses pyridine dibromide sulfate solution as halogenating agent and an incubation time of 5 min.
Measurement of iodine value with the official method is time-consuming (incubation time of 30 min with Wijs solution) and uses hazardous reagents and solvents. Several non-wet methods have been proposed for determining the iodine value. For example, IV of pure fatty acids and acylglycerols can be theoretically calculated as follows:
For fats and oils, the IV of the mixture can be calculated from the fatty acid composition profile as determined by gas chromatography (AOAC Cd 1c-85; ISO 3961:2018). However this formula does not take into consideration the olefinic substances in the unsaponifiable fraction. Therefore, this method is not applicable for fish oils as they may contain appreciable amounts of squalene.
IV can be also predicted from near-infrared, FTIR and Raman spectroscopy data using the ratio between the intensities of ν(C=C) and ν(CH2) bands. High resolution proton-NMR provides also fast and reasonably accurate estimation of this parameter.
Although modern analytical methods (such as GC) provides more detailed molecular information including unsaturation degree, the iodine value still widely considered as an important quality parameter for oils and fats. Moreover, IV generally indicates oxidative stability of the fats which directly depend on unsaturation amount. Such a parameter have a direct impact on the processing, the shelf-life and the suitable applications for fat-based products. It is also of a crucial interest for lubricants and fuel industries. In biodiesel specifications, the required limit for IV is 120 g I2/100 g, according to standard EN 14214.
G. Knothe (2002)  criticized the use of IV as oxidative stability specification for fats esterification products. He noticed that not only the number but the position of double bonds is involved in oxidation susceptibility. For instance, linolenic acid with two bis-allylic positions (at the carbons no. 11 and 14 between the double bonds Δ9, Δ12 and Δ15) is more prone to autoxidation than linoleic acid exhibiting one bis-allylic position (at C-11 between Δ9 and Δ12). Therefore, Knothe introduced alternative indices termed allylic position and bis-allylic position equivalents (APE and BAPE), which can be calculated directly from the integration resultas of chromatographic analysis.
Iodine value helps to classify oils according to the degree of unsaturation into drying oils, having IV > 150 (i.e. linseed, tung), semi-drying oils IV : 125 – 150 ( soybean, sunflower) and non-drying oils with IV < 125 (canola, olive, coconut). The IV ranges of several common oils and fats is provided by the table below.
|Fat||Iodine value (gI/ 100g)|
|Beef tallow||42 – 48|
|Beeswax||7 – 16|
|Butter||25 – 42|
|Canola oil||110 – 126|
|Castor oil||81 – 91|
|Cocoa butter||32 – 40|
|Coconut oil||6 – 11|
|Cod liver oil||148 – 183|
|Corn oil||107 – 128|
|Cottonseed oil||100 – 115|
|Fish oil||190 – 205|
|Grape seed oil||94 – 157|
|Hazelnut oil||83 – 90|
|Jojoba oil||80 – 85|
|Kapok seed oil||86 – 110|
|Lard||52 – 68|
|Linseed oil||170 – 204|
|Olive oil||75 – 94|
|Oiticica oil||139 – 185|
|Palm kernel oil||14 – 21|
|Palm oil||49 – 55|
|Peanut oil||82 – 107|
|Pecan oil||77 – 106|
|Pistachio oil||86 – 98|
|Poppyseed oil||140 – 158|
|Rapeseed oil||94 – 120|
|Rice bran oil||99 – 108|
|Safflower oil||135 – 150|
|Sesame oil||100 – 120|
|Sunflower oil||110 – 145|
|Soybean oil||120 – 139|
|Tung oil||160 – 175|
|Walnut oil||132 – 162|
|Wheat germ oil||115 – 128|