Production of oxygen-15 gas edit

Oxygen-15 can be produced by different nuclear reactions, including ¹⁴N(d,n)¹⁵O, ¹⁶O(p,pn)¹⁵O and ¹⁵N(p,n)¹⁵O.

The ¹⁴N(d,n)¹⁵O production route is the most frequently applied method, because it is currently the most economic method. The production requires a cyclotron that can accelerate deuterons up to a kinetic energy of approximately 7 MeV.^[1]

Alternatives methods are:

¹⁵N(p,n)¹⁵O, in which low-energy protons (≈ 5 MeV) are used to transmute nitrogen into oxygen-15,^[2] or ¹⁶O(p,pn)¹⁵O in which high-energy protons (> 16.6 MeV) are used.^[3][4] They all produce the radioactive isotope oxygen-15 by knocking neutrons out of the target molecule where the oxygen-15 ion combines with an oxygen atom to form the stable oxygen gas [¹⁵O]O₂:

${\displaystyle {\ce {^{14}_{7}N + ^{2}_{1}D -> ^{15}_{8}O^2- +n}}}$ 

${\displaystyle {\ce {2^{15}_{8}O^2- + N_2 -> 2 NO}}}$ 

${\displaystyle {\ce {2 NO -> [^15O]O_2 + N_2}}}$ 

Conversion of ¹⁵O gas to ¹⁵O-water edit

The conversion of the oxygen gas [¹⁵O]O₂ to ¹⁵O-water can happen in two ways: the in-target production and the out-of-target external conversion.

The in-target production method uses a small amount of hydrogen (about 5%) that is added to the gas, whereby ¹⁵O-water is formed and trapped in a cooled stainless steel loop. By heating the loop the ¹⁵O-water will get released and will be trapped again in a saline solution. It could also be done by directly irradiating H₂¹⁶O. However, this method requires high-energy protons and is therefore used less.^[5]

The external out-of-target method converts oxygen-15 and H₂ using heat and is used for all three nuclear reactions. Palladium is typically used as a catalyst to lower the activation energy. The mixture of the target gas, the catalyst and H₂ is then heated up, which results in a release of ¹⁵O-water vapor, which then bubbles into a saline solution and is drawn into a syringe where it can be applied to the subject.^[5]

Oxygen-15 decays with a half-life of about 2.04 minutes to nitrogen-15, emitting a positron.^[6] The positron quickly annihilates with an electron, producing two gamma rays of about 511 keV which are detectable using a PET scanner.^{[citation needed]}

Of several available PET tracers for quantification of myocardial blood flow (MBF), ⁸²Rb, ¹³NH₃, and H₂¹⁵O are most commonly used. (see the table below). ¹⁵O-water features different properties compared to ⁸²Rb and ¹³NH₃.

¹⁵O-water is metabolically inert and diffuses freely across the myocyte membrane in contrast to ⁸²Rb and ¹³NH₃, which enter the cell via active diffusion (¹³NH₃ diffuses both actively and passively). ¹³NH₃ is converted to glutamine, glutamic acid and carbamoyl phosphate in the tissue and becomes metabolically bound.

¹⁵O-water has a 100% extraction rate, which makes ¹⁵O-water superior to ⁸²Rb and ¹³NH₃ as no flow-dependent extraction corrections are required. Its 2-minute half-life makes it possible to acquire multiple image scans in rapid sequence. However, due to the complete extraction and free diffusibility, ¹⁵O-water is not retained in the tissue of interest and post-processing is required to convert ¹⁵O-water images to quantitative blood flow images.^[7]

Limitations edit

A technical limitation of ¹⁵O-water is the challenge in separating the blood activity from the myocardial tissue activity. This challenge arises from the tracer's free diffusion and from the fact that the tracer is metabolically inert. However, these issues have been overcome by recent advances in both hardware and software. ¹⁵O-water has now been used in several clinical trials (pivotal studies).^[5]

Another limitation for the tracer's widespread uptake has been its historical cost. A cyclotron is necessary for the production of ¹⁵O-water, requiring large capital investment in hardware and skilled staff to operate the production.^[8] However, ongoing development aims to reduce the capital expenditure and limit the amount of skilled personnel involved in the production, making ¹⁵O-water available for clinical practice.

Clinical interpretation of ¹⁵O-water PET edit

With ¹⁵O-water PET, the optimal cutoffs for detecting hemodynamically significant CAD measured by FFR have been determined to be < 2.3 mL/min/g for vasodilator stress MBF and < 2.5 for coronary flow reserve (CFR).^{[9] 15}O-water PET has an accuracy of 85% for diagnosing hemodynamically significant epicardial stenoses in patients with no history of CAD, which is higher than with both SPECT and CCTA.^[10] However, the accuracy is reduced to 75% in patients with previous myocardial infarctions and/or previous PCI.^[11]

Patients are generally considered to have a perfusion defect if stress MBF is < 2.3 mL/min/g in at least 2 adjacent segments.^[12] Patients with perfusion defects of at least 10% of the left ventricle should be referred for coronary angiography and if FFR is ≤ 0.8 they can be treated with PCI.

Besides hemodynamically significant epicardial stenoses, patients can also have coronary microvascular dysfunction (CMD).^[13] If stress MBF is reduced in the entire left ventricle, then both CMD and balanced three-vessel disease are possible diagnoses. CMD is treated pharmacologically and balanced three-vessel disease is treated surgically with CABG. It can be difficult to differentiate between CMD and balanced three-vessel disease.^[12] However, CMD is much more common than balanced three-vessel disease. Also, the calcium score from the CT scan can help in the differentiation. If the calcium score is high, then balanced three-vessel disease is more likely; and vice versa if the calcium score is low then CMD is more likely.

Pharmacopeia edit

The clinical use of ¹⁵O-water in routine is not widespread. Within the European Union, ¹⁵O-water is recognized as a radiopharmaceutical and regulated as a drug.^{[citation needed]} A pharmacopeia monograph exists, allowing hospital facilities to produce and use ¹⁵O-water within the confines of their national legislation. In the US, ¹⁵O-water is recognized as a radiopharmaceutical and regulated as a drug, but no pharmacopeia monograph exists currently.