TRI-D (rocket engine)

Summary

TRI-D is a 3D printed metal rocket engine. Students from the Students for the Exploration and Development of Space at [1][2] University of California, San Diego (SEDS at UC San Diego) built the metal rocket engine using a technique previously confined to NASA, using a GPI Prototype and Manufacturing Services printer[1] via the Direct metal laser sintering (DMLS) method.[1] UCSD students were the first group in the world to 3D print a rocket engine of its size, other than NASA as of February 2014.[3] The Tri-D engine cost US$6,800.[1][4][5]

TRI-D
Country of originUnited States
ManufacturerStudents for the Exploration and Development of Space
Application3rd stage of 3 Stage Cubesat
Liquid-fuel engine
PropellantLOX / RP-1 (rocket grade kerosene)
Performance
Thrust, sea-level0.89 kN (200 lbf)

Development edit

The Tri-D rocket engine was designed and built with the cooperation of NASA’s Marshall Space Flight Center, to explore the feasibility of printed rocket components. It was designed to power the third stage of a Nanosat or Cubesat launcher, i.e. an engine capable of launching satellites that weigh less than 1.33 kg (2.93 lb).[1][2][5]

Specifications edit

Tri-D is around 17.7 cm long and weighs around 4.5 kg. It was fabricated using a chromium-cobalt alloy powder. The propellants are kerosene and liquid oxygen. The engine produces about 200 pounds-force (890 newtons; 91 kilograms-force) thrust. According to Gizmag "the injector has a Fuel-Oxidizer-Oxidizer-Fuel inlet arrangement with two outer fuel orifices converging with two inner oxidizer orifices".[1][4]

The engine has a regenerative cooling jacket that extends to the nozzle to prevent the engine from overheating while firing. The combustion chamber was designed to burn the propellants in the middle of the chamber and keep as much heat generated as possible away from its chamber walls, while at the same time insulating the wall with a film of cooler gases.[1]

Printer edit

The engine was printed with a GPI Prototype and Manufacturing Services printer using a technique called Direct metal laser sintering (DMLS). In the process of printing, a powder of the chromium-cobalt alloy is spread in a thin layer. Then computer-controlled laser fuses the powders into a cross section of the engine component. The machine then spreads a second layer of powder and the process continuously repeats until each component is complete. Any excess powder is removed as are temporary supports that were printed to hold the components together during printing process. Finally it is hardened, polished and assembled.[1][4]

Test firing edit

The test firing at Mojave went without any problems and the engine exhaust achieved 200 pounds-force (890 newtons; 91 kilograms-force) thrust. The team claimed "it was a resounding success and could be the next step in the development of cheaper propulsion systems and a commercializing of space".[1]

Injector test edit

On a separate engine, a 3D printed injector was test fired in a conventionally manufactured engine. In the test of the injector on August 22, 2014, the engine generated 20,000 pounds-force (89,000 newtons; 9,100 kilograms-force) thrust.[2]

References edit

  1. ^ a b c d e f g h i UCSD students test fire 3D-printed metal rocket engine, gizmag, October 12, 2013. (archive)
  2. ^ a b c 3D-Printed Rocket Engine Built By Students Passes Big Test (Video), Space.com, October 08 2013. (archive)
  3. ^ UCSD group plans second 3-D printed rocket engine test to gather more data - 10News.com KGTV ABC10 San Diego, 10News, February 25, 2014. (archive)
  4. ^ a b c University students successfully tested 3D printed rocket engine, 3Ders, October 7, 2013. (archive)
  5. ^ a b Students successfully hot test 3D printed rocket engine, design-engineering, October 10, 2013. (archive)