Vintage scuba is scuba equipment dating from 1975 and earlier, and the practice of diving using such equipment.
The most striking and well recognized example of vintage scuba gear is the twin-hose or double hose regulator, a popular style of regulator in the early years of scuba diving, since Jacques-Yves Cousteau and Emile Gagnan pioneered the first such design, the C45 Scaphandre Autonome, which was marketed in the USA (along with a tank and harness) as the Aqua-Lung. The durability of the regulators from the 1950s through the early 1970s lent them to easily be refurbished and restored. Since 2007, Vintage Double Hose, in Wesley Chapel, Florida, has been manufacturing parts for original regulators as well as a modern version of the double-hose scuba regulator. The regulator is composed of modern polymers and specialty metals.[clarification needed] It allows for additional scuba equipment to be attached, such as a submersible pressure gauge, which overcomes one of the problems of the original double hose regulators which were not able to incorporate accessories.
A number of manufacturers produced integral reserve regulators in 1961 and 1962 with reasonable market acceptance. These regulators provided a lever operated mechanical reserve valve that restricted air flow when the pressure was below 500 psi. Alerted to having a low gas supply the diver would pull a rod to open the reserve valve and surface using the remaining gas. This feature provides reserve capacity on cylinders with plain valves. With this arrangement the reserve rod must also be transferred to the cylinder in use.: 166, 167
In this unusual configuration the cylinder(s) are on the diver's back and are connected by a low pressure hose to a twin-hose regulator on the diver's chest.
There have been some cases of a single-hose regulator final stage built into a full-face mask so that the mask's big front window, in conjunction with a flexible rubber seal joining it to its frame, functioned as a large and sensitive regulator diaphragm:
Invented in 1916 by Riichi Watanabi and the blacksmith Kinzo Ohgushi, and used with either surface supplied air or a 150 bar steel scuba cylinder holding 1000 litres free air, the valve supplied air to a mask over the diver's nose and eyes and the demand valve was operated by the diver's teeth. Gas flow rate was proportional to bite force. The breathing apparatus was used successfully for fishing and salvage work and by the military Japanese Underwater Unit until the end of the Pacific War.
These unusual regulators were designed by Robert J. Dempster and made at his factory in Illinois, USA, from 1961 to 1965. The Demone Mark I and Demone Mark II are both two-stage regulators. The second-stage looks like the mouthpiece of a twin-hose regulator but has a small diaphragm on the front. The second-stage valve is inside the mouthpiece tube. The exhaled air goes into a corrugated coaxial exhaust hose which surrounds the low pressure hose and discharges about 60% of the way back to the first-stage to keep the bubbles away from the diver's face. Near the mouthpiece is a one-way valve to let outside water into the exhaust hose to avoid free flow if the diaphragm (at the mouth) is below the open end of the exhaust hose. The Mark I has hoses only on one side, and the Mark II has twinned low pressure hoses, each with its own coaxial exhaust hose and second stage, one assembly on each side of the diver's head, but with both second stages in the same mouthpiece housing and operated by the same diaphragm.: 93–100  This version has a small second stage.
This system is unusual in that it used a single stage single hose demand valve in a full-face mask. The high pressure supply hose routes over the shoulder, but from an inverted cylinder, which allows the user to easily reach the valve.: 249–253
For a few years in the mid-1950s, Dräger made the Dräger Delfin II (their first scuba regulator - it was marketed as the Barakuda (now IAC) in the USA): this was a single stage single hose "pendulum"" regulator with only one ambient pressure (corrugated) hose: the exhaled air went back down the hose to the cylinder mounted regulator and was released to outside through a one-way valve inside the casing. The end of the flexible tube was connected to the mouthpiece by a short quarter-circle of hard tube. The two way hose would have caused dead space similar to a rebreather with a pendulum system.
The first single-hose open-circuit scuba made by Ted Eldred in Melbourne, Australia. It was designed in 1948 to avoid the Cousteau-Gagnan aqua-lung patent, and to get rid of air supply restrictions that affected early Cousteau-Gagnan-type aqua-lungs. Commercial production started in 1952. The Royal Australian Navy adopted it, and it popular with Australian recreational scuba divers. The model CA-1 was used on one cylinder with its valve at the bottom, strapped directly to the back with rucksack-type straps without backpack plate or buoyancy aid, with a single-hose regulator-mouthpiece which could be strapped in. The tank was inverted so that the diver could reach the regulator mounted reserve handle. The head strap was intended to keep the demand valve from falling well below the diver, if dropped from the mouth. The high-pressure regulator screwed into the outlet of the cylinder valve. Versions were made for the Australian Navy until 1976, and the last one known to be sold to the public was sold in that year. About 12,000 Porpoise units of all models were produced, of which about 50 still exist. Only a few of the early models are known today, the rarest being the CA-2, made for use with two tanks.[clarification needed]
In the early years of scuba diving in Britain, "tadpole" was a nickname for a type of diving gear that had two meanings:
The concept of a diving regulator where the energy released as the air expands from cylinder pressure to the surrounding pressure as the diver inhales, is used to power a propeller has been patented, but no product ever appeared on the market.
In 1956 and for some years afterwards in Britain, factory-made aqualungs were very expensive, and many aqualungs of this type were made by sport divers in diving clubs' workshops, using miscellaneous industrial and war-surplus parts. One necessary raw material was a Calor Gas bottled butane gas regulator, whose 1950s version was like an aqualung regulator's second stage but passed gas all the time because its diaphragm was spring-loaded; conversion included changing the spring and making several big holes in the wet-side casing. The cylinder was often an ex-RAF pilot's oxygen cylinder; some of these cylinders were called tadpoles from their shape.
A design was described in Practical Mechanics magazine in January 1955, for a home-made aqualung with a first-stage on the cylinder top leading through a low pressure hose to a converted Calor Gas regulator on the diver's chest connected to the diver's mouthpiece by a twin-hose loop.
The complete Draeger twin 7 litre 200 bar scuba set with twin hose regulator
An early Aqualung set.
The Nemrod Snark III silver regulator is typical of the older twin-hose type.