|Mohs scale hardness||8.0-8.5|
|Specific gravity||5.6-6.0 g/cm3|
Cubic zirconia (CZ) is the cubic crystalline form of zirconium dioxide (ZrO2). The synthesized material is hard and usually colorless, but may be made in a variety of different colors. It should not be confused with zircon, which is a zirconium silicate (ZrSiO4). It is sometimes erroneously called cubic zirconium.
Because of its low cost, durability, and close visual likeness to diamond, synthetic cubic zirconia has remained the most gemologically and economically important competitor for diamonds since commercial production began in 1976. Its main competitor as a synthetic gemstone is a more recently cultivated material, synthetic moissanite.
Cubic zirconia is crystallographically isometric, an important attribute of a would-be diamond simulant. During synthesis zirconium oxide naturally forms monoclinic crystals, which are stable form under normal atmospheric conditions. A stabilizer is required for cubic crystals (taking on the fluorite structure) to form, and remain stable at ordinary temperatures; typically this is either yttrium or calcium oxide, the amount of stabilizer used depending on the many recipes of individual manufacturers. Therefore, the physical and optical properties of synthesized CZ vary, all values being ranges.
It is a dense substance, with a density between 5.6 and 6.0 g/cm3—about 1.65 times that of diamond. Cubic zirconia is relatively hard, 8–8.5 on the Mohs scale—slightly harder than most semi-precious natural gems. Its refractive index is high at 2.15–2.18 (compared to 2.42 for diamonds) and its luster is vitreous. Its dispersion is very high at 0.058–0.066, exceeding that of diamond (0.044). Cubic zirconia has no cleavage and exhibits a conchoidal fracture. Because of its high hardness, it is generally considered brittle.
Under shortwave UV cubic zirconia typically fluoresces a yellow, greenish yellow or "beige". Under longwave UV the effect is greatly diminished, with a whitish glow sometimes being seen. Colored stones may show a strong, complex rare earth absorption spectrum.
The high melting point of zirconia (2750 °C or 4976 °F) hinders controlled growth of single crystals. However, stabilization of cubic zirconium oxide had been realized early on, with the synthetic product stabilized zirconia introduced in 1929. Although cubic, it was in the form of a polycrystalline ceramic: it was used as a refractory material, highly resistant to chemical and thermal attack (up to 2540 °C or 4604 °F).
In 1937, German mineralogists M. V. Stackelberg and K. Chudoba discovered naturally occurring cubic zirconia in the form of microscopic grains included in metamict zircon. This was thought to be a byproduct of the metamictization process, but the two scientists did not think the mineral important enough to give it a formal name. The discovery was confirmed through X-ray diffraction, proving the existence of a natural counterpart to the synthetic product.
As with the majority of grown diamond substitutes, the idea of producing single-crystal cubic zirconia arose in the minds of scientists seeking a new and versatile material for use in lasers and other optical applications. Its production eventually exceeded that of earlier synthetics, such as synthetic strontium titanate, synthetic rutile, YAG (yttrium aluminium garnet) and GGG (gadolinium gallium garnet).
Some of the earliest research into controlled single-crystal growth of cubic zirconia occurred in 1960s France, much work being done by Y. Roulin and R. Collongues. This technique involved molten zirconia being contained within a thin shell of still-solid zirconia, with crystal growth from the melt. The process was named cold crucible, an allusion to the system of water cooling used. Though promising, these attempts yielded only small crystals.
Later, Soviet scientists under V. V. Osiko in the Laser Equipment Laboratory at the Lebedev Physical Institute in Moscow perfected the technique, which was then named skull crucible (an allusion either to the shape of the water-cooled container or to the form of crystals sometimes grown). They named the jewel Fianit after the institute's name FIAN (Physical Institute of the Academy of Science), but the name was not used outside of the USSR. This was known at the time as the Institute of Physics at the Russian Academy of Science. Their breakthrough was published in 1973, and commercial production began in 1976. In 1977 cubic zirconia began to be mass-produced in the jewelry marketplace by the Ceres Corporation with crystals stabilized with 94% yttria. Other major producers as of 1993 include Taiwan Crystal Company Ltd, Swarovski and ICT inc. By 1980 annual global production had reached 60 million carats (12 tonnes) and continued to increase with production reaching around 400 tonnes per year in 1998.
Because the natural form of cubic zirconia is so rare, all cubic zirconia used in jewelry has been synthesized, or created by humans.
Currently the primary method of cubic zirconia synthesis employed by producers remains to be through the skull-melting method. This method was patented by Josep F. Wenckus and coworkers in 1997. This is largely due to the process allowing for temperatures of over 3000 degrees to be achieved, lack of contact between crucible and material as well as the freedom to choose any gas atmosphere. Primary downsides to this method include the inability to predict the size of the crystals produced and it is impossible to control the crystallization process through temperature changes.
Zirconium dioxide thoroughly mixed with a stabilizer (normally 10% yttrium oxide) is fed into a cold crucible. Metallic chips of either zirconium or the stabilizer are introduced into the powder mix in a compact pile manner. The RF generator is switched on and the metallic chips quickly start heating up and readily oxidize into more zirconia. Consequently, the surrounding powder heats up by thermal conduction and begins melting, which in turn becomes electroconductive and thus it begins to heat up via the RF generator as well. This continues until the entire product is molten. Due to the cooling system surrounding the crucible, a thin shell of sintered solid material is formed. This causes the molten zirconia to remain contained within its own powder which prevents it from contamination from the crucible and reduces heat loss. The melt is left at high temperatures for some hours to ensure homogeneity and ensure all impurities have evaporated. Finally, the entire crucible is slowly removed from the RF coils to reduce the heating and let it slowly cool down (from bottom to top). The rate at which the crucible is removed from the RF coils is chosen as a function of the stability of crystallization dictated by the phase transition diagram. This provokes the crystallization process to begin and useful crystals begin to form. Once the crucible has been completely cooled to room temperature, the resulting crystals are multiple elongated-crystalline blocks.
The reason behind this shape is dictated by a concept known as crystal degeneration according to Tiller. The size and diameter of the obtained crystals is a function of the cross-sectional area of the crucible, volume of the melt and composition of the melt. The diameter of the crystals is heavily influenced by the concentration of Y2O3 stabilizer.
When observing the phase diagram the cubic phase will crystallize first as the solution is cooled down no matter the concentration of Y2O3. If the concentration of Y2O3 is not high enough the cubic structure will start to break down into the tetragonal state which will then break down into a monoclinic phase. If the concentration of Y2O3 is between 2.5-5% the resulting product will be PSZ (partially stabilized zirconia) while monophasic cubic crystals will form from around 8-40%. Below 14% at low growth rates tend to be opaque indicating partial phase separation in the solid solution (likely due to diffusion in the crystals remaining in the high temperature region for a longer time). Above this threshold crystals tend to remain clear at reasonable growth rates and maintains good annealing conditions.
Because of cubic zirconia's isomorphic capacity it can be doped with several elements to change the color of the crystal. A list of specific dopants and colors produced by their addition can be seen below.
|Color Range||Dopant Used|
Purple cubic zirconia with checkerboard cut
Multi-color cubic zirconia
Three-tone cubic zirconia gems
Yellow cubic zirconia
The vast majority of YCZ (yttrium bearing cubic zirconia) crystals clear with high optical perfection and with gradients of the refractive index lower than . However some samples contain defects with the most characteristic and common ones listed below.
Due to its optical properties YCZ (yttrium cubic zirconia) has been used for windows, lenses, prisms, filters and laser elements. Particularly in the chemical industry it is used as window material for the monitoring of corrosive liquids due to its chemical stability and mechanical toughness. YCZ has also been used as a substrate for semiconductor and superconductor films in similar industries.
Mechanical properties of partially stabilized zirconia (high hardness and shock resistance, low friction coefficient, high chemical and thermal resistance as well as high wear and tear resistance) allow it to be used as a very particular building material. Particularly in the bio-engineering industry, it has been used to make reliable super-sharp medical scalpels for doctors that are compatible with bio tissues and contain an edge much smoother than one made of steel.
In recent years[when?] manufacturers have sought ways of distinguishing their product by supposedly "improving" cubic zirconia. Coating finished cubic zirconia with a film of diamond-like carbon (DLC) is one such innovation, a process using chemical vapor deposition. The resulting material is purportedly harder, more lustrous and more like diamond overall. The coating is thought to quench the excess fire of cubic zirconia, while improving its refractive index, thus making it appear more like diamond. Additionally, because of the high percentage of diamond bonds in the amorphous diamond coating, the finished simulant will show a positive diamond signature in Raman spectra.
Another technique first applied to quartz and topaz has also been adapted to cubic zirconia: vacuum-sputtering an extremely thin layer of a precious metal (typically gold) or even certain metal oxides or nitrides amongst other coatings onto the finished stones creates an iridescent effect. This material is marketed as "mystic" by many dealers. Unlike diamond-like carbon and other hard synthetic ceramic coatings, the effect is not durable with decorative precious metal coatings due to their extremely low hardness compared to the substrate along with poor abrasion wear properties.
There are a few key features of cubic zirconia which distinguish it from diamond:
Regarding value, the paradigm that diamonds are costly due to their rarity and visual beauty has been replaced by an artificial rarity attributed to price-fixing practices of De Beers Company which held a monopoly on the market from the 1870s to early 2000s. The company pleaded guilty to these charges in an Ohio court in 13 July 2004. However, while De Beers has less market power, the price of diamonds continues to increase due to the demand in emerging markets such as India and China. The emergence of artificial stones such as cubic zirconia with optic properties similar to diamonds, could be an alternative for jewelry buyers given their lower price and noncontroversial history.
An issue closely related to monopoly is the emergence of conflict diamonds. The Kimberley Process (KP) was established to deter the illicit trade of diamonds that fund civil wars in Angola and Sierra Leone. However, the KP is not as effective in decreasing the number of conflict diamonds reaching the European and American markets. Its definition does not include forced labor conditions or human right violations. A 2015 study from the Enough Project, showed that groups in the Central African Republic have reaped between US$3 million and US$6 million annually from conflict diamonds. UN reports show that more than US$24 million in conflict diamonds have been smuggled since the establishment of the KP. Diamond simulants have become an alternative to boycott the funding of unethical practices. Terms such as “Eco-friendly Jewelry” define them as conflict free origin and environmentally sustainable. However, concerns from mining countries such as the Democratic Republic of Congo are that a boycott in purchases of diamonds would only worsen their economy. According to the Ministry of Mines in Congo, 10% of its population relies on the income from diamonds. Therefore, cubic zirconia are a short term alternative to reduce conflict but a long term solution would be to establish a more rigorous system of identifying the origin of these stones.