Fundamental Electrical Connections

There's just practically nothing like mastering electric wiring! As children we marveled in the "magic" of electricity, but even now as adults, we nevertheless can't enable but stand in awe at its power. We may not know exactly how and why it functions, but we do realize that it does. By following some standard wiring concepts, you'll be able to more than just recognize its power. You'll have in your arsenal the capability to harness that power and use it as you see match. I've covered safety in previous articles so I'll assume you will be aware of the potential dangers of electricity and how to stay away from them. Get far more details about   подключение электричества к участку без дома



I'll be going over some standard connection approaches that you could incorporate promptly within your personal home wiring. In theory, most home electric wiring is basically extending wire from you main breaker panel to all the several outlets and lights about your house. So let's say you may have 20 20 amp breakers inside your most important panel and you happen to be already using 10. You wish to draw power towards the new area you're inside the process of creating and you happen to be questioning ways to go about it. Now if there was only 1 outlet you needed power for, this would not involve any mid-way connections.



Forgive me if I'm wrong, but I'd say for most rooms you'd want at the least 1 outlet and 1 light. And already right here you'll be needing your connection. The difficult issue about lights is that you typically desire to attach a switch as well - which tends to make the connection somewhat far more difficult. After you get used for the idea it won't be so challenging. Within this article I'll only be going by way of the connection process, not the "what to connect to what". Keep in mind to only connect towards the principal breaker right after Anything else has been attached and you will find no naked wires. Before we start, you'll be needing the following:



1. Crimper. This really is to crimp 2 or much more copper wires together.



2. Wire stripper. For stripping the thin insulation off person cables.



3. Utility knife. Use this to slice away thick outer insulation.



4. Crimp connectors. You are going to be needing a generous load of those small guys. By the way, these are the little triangular shaped factors in the ends from the connections around the diagram which you'll be crimping 2 or a lot more cables with.



5. Electric tape. For taping connections with each other following crimping.



6. Nylon bands. These could possibly be deemed an overkill, but I take safety seriously.



Ok, now that we've got what we will need, let's commence.



1. With your utility knife, strip away an proper amount of outer insulation, exposing the person "colored" cables inside.



2. Now along with your wire stripper, strip slightly much more than one crimp connector's length of insulation from every of the cables. The concept should be to bare only what's necessary and no additional.



3. Take your connectors and begin crimping them collectively together with your crimper tool. There will likely be varying connector sizes depending on how a lot of cables you might be crimping together, so pick the appropriate sizes. Note that crimping correctly is just as vital because the crimping act itself - make certain that the connection is rock-solid and that there is certainly zero movement once you tug forcefully on the cables. You need to crimp the connector in quite a few points to make sure maximum bond. You shouldn't overlap cables in an "X" fashion when crimping, but need to aim for a parallel connection.



4. Completely tape all connections with electric tape.



5. Tighten bands around all finished connections and clip off excess. This ensures the electric tape doesn't come loose more than time - which CAN happen otherwise. Adding an additional band about the conjoined cables 5 or so centimeters under the connection ensures the individual cables do not accidentally get "pulled" apart.



There you've your connection! Note that you'll find alternatives to crimping including tiny connector boxes, but they're more pricey and not suitable for outdoor use - rainwater gets trapped inside and may bring about shorting. For those who do use these, ensure to stick only to indoor use and bend the connection upward so the "entrance" is facing down. The pros to these connectors is the fact that they make connecting cables really rapid and very simple. Another critical point is evenly distributing your electric load to your individual breakers as this can save you money in your electric bill more than time.